• Sourcing Solutions
  • Services & Membership
  • Help & Community

DL011PC----One Din Car PC 

1. Can you add for model DL011PC- SIRF3-GPS, what will be the extra cost-?

-------Yes. we can add the SIRF 3-GPS function for the DL011PC, but the SIRF3-GPS is external, not inside the model, because our R&D dept said if we inside the GPS in the model, that would be receive the poor signal, so we adopt to the external GPS in order to receive the good signal, moreover you can put the GPS anywhere in car.If you need the GPS receiver, you need extra cost USD45.  Attached is the GPS receiver spec for your reference. 


2.If the DL011PC has a D V D-ROM inside?

-------Sorry, it can not. If you need the pc with D V D/C D-ROM, you just use another pc case with D V D/C D-ROM to do it.



1. Is it possible to remove the HDD of the pc because I'll install SSD Hard Drive

-------Yes, it can. There are two kinds chipset of SSD hard driver, one is MLC chipset, if you need it, then just add USD75; another chipset is SLC, if you need it, then need add USD252, this is very expensive price, the MLC chipset SSD transfer speed is slower than SLC chipset SSD. Which kinds of SSD are you need?


2. Customer said : WE NEED THE CAR PC WITH OUR specification.


(1)does it have window s, and can we install any window s anytime?

-------No, it is not included the software(Window system),we don't sell software, usually our customers buy our PC and install the system by themselives, of course you can install window s system anytime. But if you need, our engineer can install a piratical window system only for your testing.

(2) can we add maps for the navigator?

-------For GPS navigator, we adopt a bluetooth GPS receiver thrught bluetooth to receive the signal. Attached are spec and photo of our bluetooth GPS receiver for your reference. You can place the bluetooth GPS receiver anywhere in car. About the map you can download it from internet or buy it from map company.

(3)can it be connected to a wireless keyboard?

-------Yes, of course it can be connected to a wireless keyboard.

(4) can we use internet through it?

-------Of course, you can use WIFI or GPRS wireless internet.

(5) how does the GPRS work? (the SIM card is inside or outside?)

-------We use the external GPRS with USB port, you can insert the GPRS to our PC through by the USB port, as for the SIM card which is inside the GPRS.

(6) how many GB is the hard disc? -------Our stardard config is 80GB hard disc, you also can change the size of hard disc according to your need.


(7) how can we charge the sim card and can we make calls or it is just used for transferring data and connecting to internet only(GPRS)?

-------Charge the sim card which similar with your mobile phone. Yes, you can make calls and connecting to internet when you using GPRS.


3. we send you the scanned passpor ts of LCD screens, and could you please suggest us, which of Mini Car PC is more proper to connect with these LCD screens. (which of those 3 kinds of Mini Car PC-s)

-------The most important question is: It seems that there is no VGA port in your LCD screen, then how it can connect PC? To explain it clearly,  i attach a photo about our LCD monitor. Could i know where will you use the lcd screen with PC? Then i  can suggest a most proper model of mini car PC.


4. Does each of these mini Car PC-s, have the function of Auto start and shut down at the same time when Car’s “starter” starts?

-------After you connect the light switch cable, the car PC will Auto start and shut down at the same time when Car's “starter” starts. And with the power management module, you can set the  PC delay time when PC open and close.



5. As for shipping and delivery dates, terms and conditions: As we understand, if we order One Mini Car PC (as a sample order), than you are available to deliver it in 2 days. And if we order you more amount, like 20 one, than the delivery time will take 2 weeks, am I right, or no?

------- If we have stock at that time, we are  available to deliver a sample in 2 days and 20PCS in two weeks. But if not stock, maybe it needs a little more time to purchase the materials and produce.


6. My hardware engineer looked at this(N270 MB) and asked to see if we can get more than 1.6G cpu speed? Can we change it to have 2g or more? If so, how much will it cost?

-------The CPU of intel Atom N270 motherboard is onboard 1.6G CPU. So the only way to get more CPU speed is to redesign the motherboard.


7. Could it be more powerful and including HDD and RAM?

-------Yes, of course you can change the HDD and RAM's size according to your needs. About the CPU, the DL012PC's CPU can be upgrade to 1.2Ghz, but DL014PC can be upgrade to 1.1Ghz.


8.Is it possible to issue a warranty card a giver purchaser, for example for a year? Can the warranty be enforcing from the data of purchase.


-------Our product's warranty is one year and from you received the goods. In a case of damage, we can send the spare parts(except the screen panel) to you for repair in your local, if you can not repair in your local, also you can send it back to us for repair, but you need to pay the freight charge.


9. We need price information O.S. included. The chippest one of Micro soft O.S. (ex. WinCe) and obviusly it must be official/original.

-------Sorry that we don’t sell O.S. systems, usually we just install a testing version system for customers testing, our customer buy our PC and install the official system by themselves.


10.(regarding mini pc) Would it be possible to add win xp home to it?

-------We don't have real win xp home. We even don't have pirating win xp home at hand. What we have installed in the PC is win xp pro and it is pirating. We try to search a pirating win xp home from internet and install it, is it ok?

Touchscreen LCD monitor products



1. DL065A-----6.5Double Din touchscreen monitor


1. When a C D is put into the slot and you press "Mode" there is only Vi deo 1, Vi deo 2 and Radio.  There is not a "C D" mode nor does C D play on any of the modes available.  Did the factory confirm whether or not the unit should be able to play C Ds?  Or did they not install the software?

-------It needs to connect the 2 DIN monitor to car PC. It can play C D only at VGA state.


2. D V D-ROM cannot play movies

-------Clients need to install play software. As the format of some C D are different, so the monitor’s original software cannot play it.

3. The problem is my touch screen keeps working even when I turned off the car. When it is on there is nothing on the screen just its black screen. When I remove the car k e y the power button will switched off but the screen is working with black screen, also I can hear the screen fan.

-------Probably it needs to replace the EEPROM of the touch screen. The brand of its EEPROM is ATMEL, model is 24C16 and encapsulation is SO-8.


2. DL070HT----7” Headrest/Stand touchscreen montior.

1. I have read your attached files and I think the best solution is the model DL070HT. As I told you we cannot install your DL070HT into the car. So, the case is not necessary.In this way we will save also 8USD, right?

-------Yes, you are right. :) 

Our idea is explained to the follow:

-------Attached are two photos of our DL070HT screen panel, we use some small sheet metals and screws to fix the screen panel to our case.

Obviously I hope there are inside this monitor some fasteners to create a sort of mechanical adaptor. In fact we will have to create our special mechanical case. Do you think it is possible? -------Yes, of course you can.

To control brightness and so on, I believe you usually use a remote controller as well as the push buttons on the front side of DL070HT.Do you think it’s possible to remote the same function using our push buttons located on our mechanical case? In other words we would like to wire these signals connecting them with our special push buttons.I believe it could be easy with your instructions.

-------Yes, of course you can use yourself push buttons for this unit, the button is just for your push action. So your means we provide you all components of this unit except the case, you can install them to your special case, right? if that, of course we can provide it to you.

3. DL070PM----7 Headrest/Stand touchscreen monitor with LED backlight.

1.It’s not correct, please see the pic point 1 included (left one from DELONG, right one from LILLUPUT). The qualitiy of the DELONG mounting ram is very bad, the silver ball could not be fixed 100%. 

 -------Checked with our purchasing dept that we can provide the right one for you.

2. Speakers are to bad, to quiet – we talked about msn before. Could you provide us the model DL070PM with better speakers (2x2 W ore better) ?

-------Yes, we can make it to 2*2W. 

3.Customer wants to have min. 5m cable – 1,5 m is to short for installation in a truck.

Another urgent point is the connector of the cable, right now we have

on one side the CETRONICS connector (see the right position of the pic point3.jpg)

and on the other side many cable (the left side of the pic). The customer wants to haveonly one connector on both ends (2 Cetronics connetors, one male, ?one female)


The length of 5m is a must for a order – otherwise the customer will pay more and will order


Directly at Lilliput (VT-70). Please could you check with your engineers if it is possible to have

a)   a cable with 2 Cetronics connectors

------- Checked with our engineer that we can do that, but at present there is a problem need to discuss. As our DL070PM monitor's connector is female, now we need to know if your PC's connector is male or female?(also you can send your PC's connector photo to us)  then we according this status to special customized the connector to meet your demands, moreover there is no any connector with one side is male and the other side is female in whole markets at present, at now the connector two side all are male in markets, so if you need the connector with one side is male and the other side is female, we just special customized for you, moreover you need to tell me your PC's connector is male or female?

-------Customer reply again: Please find enclosed the picture with the cable male / male. Male / Male would be ok, our customer has to develop the adapter on your connector.Please could you sent me the additional price for the new cable?


-------Checked with our engineer that we can make the Male/Male connector to you for free.


For the Male/Male connector, one side is connect with our DL070PM, the other side is connect with your equipment, so you need give the other side connector's ports definitions to our engineer, then we can make the Male /Male connector to you.


*******Customer reply again: please could you give us the price for 2,5m (3m) and 5m male/male cable.


-------Our standard cable is 1.5M.


2.5M: add USD3


3M: add USD3.5


5M: add USD9




b) and 5m length

-------Checked with our engineer that you just prolong the VGA and USB cables, we can additional match the 5m VGA and 5m USB prolong wires for you, you need to pay more USD8 for per unit. But our engineer do not suggest you to do that, because the cables is more long, the transfers signal is more poor, so our engineer would not suggest you use the 5m prolong cables.


7.when i plug in the adaptor, the red lights blings and goes off ... no sound , no picture ....What’s the problem?

-------When you use the adaptor, please join the " +" cable and “light switch cable” together, then the monitor can work normally.

8. (Regarding DL070PM) The touch screen cursor is inverted. When I move the stylus up, the pointer goes down, move left , it goes right. The cursor and stylus meet in the middle of the screen.

---------1.After you install touch driver, you can find a icon named " Touchkit open" on your computer's user interface. Open it. Then you will see a touch calibration image.

2. Click "Tools " button.

3. Choose " clear and calibrate". Go on step by step.

4. If the touch is still not accurate, continue to choose " Linearization" , just below the row of " clear and calibrate". Go on step by step.




4.DLG070----7 Taxi advertising player


1. Would you please let us know the battery capacity of DLG070 taxi advertising player?

--------It doesn't have battery inside. It is connected to DC12V power supply.

2. Question: For the 7inch open frame monitor, we need only a VGA connection, we don´t need IR remote control, speakers, Can you customize a little your product?

Answer: We can make our product just with VGA port and USB touch to meet your needs.

For 7", we have one cable, it just has VGA and USB port. So it is very fit for you.


5.DL080HT----8” Headrest touchscreen montior.

1. About 8” headrest monitor,in regards to what I mentioned about the “headphone jack”, I meant that the 8” headrests should have cables to connect the sound output from the PC to the headrests. I am concerned about this as you have not explained how the sound will go from the PC to the headrests’ speakers. 

-------I have discussed with our engineer about the headphone jack problem, as our original mould without the headphone jack, if you real need the headphone jack on the samples of DL080HT,we can have a try to make a headphone jack by manual on the DL080HT this time, if that the appearance of this unit maybe is not enough beautiful, as this is only as the samples for you, so when you place the mass order, then we would modify our moulds with headphone jack for you.


6.DL080A----8 touchscreen LCD montior

Q: why connect 8” monitor with my notebook, the 8” have not the image?

A: Because you have not set the screen display is double display, pls set your notebook screen is double display, then the 8” monitor have image.


7.DLG089---8.9 open frame touchscreen monitor



1.we use either then 8.9" HannStar 1024x600y display or the 8.9" T oshiba   1280x768y display or the 5.6" T oshiba 1024x600y display. Do you have vi deo boards for either of them?


--------We need the display sample to write the vi deo board's drive program, and to make its interfaces.




8.DL104C----10.4 touchscreen LCD monitor




1. Could you send me picture, price and specification for monitor DL104B or any 10.4” touch screen monitor that is design for -40 -60 temperature.


-------The working temperature of our present 10.4" touch screen monitor (DL104C) is 0 - 60 temperature. Its highest resolution is 1920*1080. I attached its specs and price. We can make it good for -40 - 60 temperature, but the highest resolution will be 800*600. Chipset which supports cold temperature can not reach very high resolution. As it is a new scheme, so the process will take about one or two months. Meanwhile, the cost will increase.


First, each motherboard will add extra 18USD.

Second, we need to use industrial lcd panel, then each lcd panel will add extra 70USD.


9.DL150A----15 Touchscreen LCD montior.


1.About 15inch monitor, do you have this model that it can is resistan to blows, liquids and heat?Because these monitors destined to a Pub restorant, the idea is to place the monitors in a table where the client realised their order with these monitors touch.

-------As your requst, DL150A is not fit for you. We have another model (DL150WP) which the housing materal can resist waterproof.